Search found 223 matches

by MrDoom
12 May 2018, 00:08
Forum: helloBEEprusa
Topic: [SOLVED] Jumping stepper motor wheels
Replies: 3
Views: 4381

Re: Jumping stepper motor wheels

Hello Mic, I think you problem is caused by a stepper driver that has not enough current. From what I remember you installed Allegro on all axis right? If so depending on the version of the stepper driver you have the voltage adjustment ( the small potentiometer, to measure the voltage take the red ...
by MrDoom
30 Apr 2018, 11:48
Forum: helloBEEprusa
Topic: I need a gcode pro!
Replies: 4
Views: 5006

Re: I need a gcode pro!

Hey there, so did it work?
by MrDoom
30 Apr 2018, 11:47
Forum: helloBEEprusa
Topic: You are too loud! Now, you're vibrating too much.
Replies: 13
Views: 13577

Re: You are too loud! Now, you're vibrating too much.

Hi there,
Yes any MKS gen 1.x board should do as they all have the same pins the changes are on the power regulation to the chip :)

Anyway you should try contacting beeverycreative just to be sure
by MrDoom
27 Apr 2018, 20:55
Forum: helloBEEprusa
Topic: You are too loud! Now, you're vibrating too much.
Replies: 13
Views: 13577

Re: You are too loud! Now, you're vibrating too much.

Hi there Mic, You migh have plugged the chips the wrong way, the potentiometer on the DRV8825 faces up on the allegro it faces down on the motherboard https://image.ibb.co/fWFcZH/a4988_drv8825_3a.jpg To be sure when changing one stepper driver model for another always check that the silkscreen on th...
by MrDoom
23 Apr 2018, 14:19
Forum: helloBEEprusa
Topic: You are too loud! Now, you're vibrating too much.
Replies: 13
Views: 13577

Re: You are to loud! Now, you're vibrating too much.

Hello Mic, I would suggest 2 changes to make you printer almost whisper quiet: - Change the PSU to a fanless one with the same power and voltage 24V 360W - Change all the stepper drivers to TMC2208 I did this and the printer is barely hearable with any ambient noise :) If you want a cheaper alternat...
by MrDoom
23 Apr 2018, 14:15
Forum: helloBEEprusa
Topic: I need a gcode pro!
Replies: 4
Views: 5006

Re: I need a gcode pro!

Hi there Mic, I think I can help you with those features, what slicer do you use? I think the first feature ca be implemented though a specific start gcode for each extruder The second feature can be implemented relatively easily on the start gcode as well, please test this code and see if it works ...
by MrDoom
21 Apr 2018, 18:57
Forum: helloBEEprusa
Topic: "No SD Card"
Replies: 1
Views: 3232

Re: "No SD Card"

Hello, by what you described, it appears your SD card is incorrectly formatted. Download sdcard formatter here https://www.sdcard.org/downloads/formatter_4/ and use it to reformat you SD card, choose the overwrite all option, it should take a few minutes and the your card should work. Of it still do...
by MrDoom
19 Apr 2018, 11:22
Forum: GENERAL
Topic: hello guy
Replies: 9
Views: 13593

Re: hello guy

Welcome to the forum :) if you have any doubt or ideas towards your printer that you want to do but need help feel free to create a new topic
by MrDoom
17 Apr 2018, 17:14
Forum: helloBEEprusa
Topic: [IMPORTANT] helloBEEprusa recommended Slicer and printing profiles
Replies: 22
Views: 30030

Re: [IMPORTANT] helloBEEprusa recommended Slicer and printing profiles

Hi there Tgala, although I have used cura intermitently, I can't still get used to it like I did to Slic3r or Simplify 3d, Cura prints well when well configured but at the same time limits or makes dificult to change some of the things I like to customize, I change a lot the printer the materials an...
by MrDoom
17 Apr 2018, 10:42
Forum: helloBEEprusa
Topic: Bed Heating and extruder temp issues
Replies: 4
Views: 5120

Re: Bed Heating and extruder temp issues

As far as I know the firmware doesn't use PID for the hotbed as this would make the bed mosfet switch to often causing it to last much less, and on the buildplate a 1ºC variation isn't something to be worried about although you could activate the function if you really desire to :) Auto bed leveling...