Search found 33 matches

by RickRick
16 Feb 2018, 21:58
Forum: helloBEEprusa
Topic: [IMPORTANT] helloBEEprusa recommended Slicer and printing profiles
Replies: 22
Views: 22638

Re: [IMPORTANT] helloBEEprusa recommended Slicer and printing profiles

Downloaded 1.38.5 32 and 64 but get the same error each time

loading a configuratio file
c:/desktop ect file name Failed

reason unspecified file charecter not found

any suggestions
by RickRick
23 Dec 2017, 09:28
Forum: helloBEEprusa
Topic: Printer just went bang
Replies: 1
Views: 3206

Printer just went bang

Hi all after a year without any major issues my printer just blew a fuse :( :( I've just fitted the second extruder again after the feed tube got twisted taking it out of action for a few weeks, i've put the heater and the thermister back into a new block, both seemed to come out easily enough and i...
by RickRick
18 Nov 2017, 19:10
Forum: helloBEEprusa
Topic: [COMMUNITY] INFO DOCUMENT - CALIBRATION GUIDE
Replies: 9
Views: 13376

Re: [COMMUNITY] INFO DOCUMENT - CALIBRATION GUIDE

Edit Ignore this, the gaps were present in slicr due to me setting the wrong nozzel size 0.5 not 04 So i'm finally printing the calibration cube I was really close after previous attempts at calibrating but now i'm getting right down to the correct size and wall thickness however the corners are not...
by RickRick
16 Sep 2017, 13:19
Forum: helloBEEprusa
Topic: [FIRMWARE] Latest helloBEEprusa firmware 1.1.1 Final
Replies: 14
Views: 19554

Re: [FIRMWARE] Latest helloBEEprusa firmware 1.1.1 Final

Got a bit of an odd issue after updating the firmware

When i set off a print, the extruder shows the correct temp, but heats to 10c below this every time i have to turn up the heat with tune, then once heated turn it back down

Any suggestions or just reload firmware?
by RickRick
31 Aug 2017, 20:45
Forum: helloBEEprusa
Topic: Coding question turn of heaters
Replies: 4
Views: 4207

Coding question turn of heaters

Ok i know nothing about Gcode
I use slicer to process stl files to print i regularly print big ish stuff that takes 12 hours plus so it ends up printing over night

Is there a simple way to turn off the heating to the bed and both extruders once printing is complete

Thanks
by RickRick
22 Jun 2017, 20:31
Forum: helloBEEprusa
Topic: Heated bed moving during printing?
Replies: 5
Views: 4902

Re: Heated bed moving during printing?

Did you try this MrDoom
by RickRick
06 Jun 2017, 18:11
Forum: helloBEEprusa
Topic: Heated bed moving during printing?
Replies: 5
Views: 4902

Re: Heated bed moving during printing?

I have an easy fix for this now, i think could be worth adding to the manual Just add a plain m3 nut under the spring. so Bolt heated plate spring plain nut bed frame washer nylon nut adjust the plain nut to clamp the bed frame lightly, this stops the bolt from moving but still lets the bed slide do...
by RickRick
25 Apr 2017, 20:24
Forum: helloBEEprusa
Topic: Bed temperature too low
Replies: 6
Views: 6129

Re: Bed temperature too low

I took a lot of time setting the bed level mechanicaly setting both Z screws with a block to start then tweaking the bed screws and Z screws to get as close as i could then did the software level if i had to adjust with software a lot i went back to mechanical adjustment
by RickRick
25 Apr 2017, 20:19
Forum: helloBEEprusa
Topic: Heated bed moving during printing?
Replies: 5
Views: 4902

Heated bed moving during printing?

Ive been printing some nylon rc car parts seem to have got very good strength between layers and the holes to locate bearings are coming out ok size wize but 2 holes same X Y different Z location are coming out slightly offset this has me wonderi g if the bed could be moving on the springs during pr...
by RickRick
25 Jan 2017, 21:06
Forum: helloBEEprusa
Topic: New Owner and some tweeks
Replies: 8
Views: 10253

Re: New Owner and some tweeks

Next stage is done now all fans mounted on one part that lifts off without any screws. No need to counter bore the heat blocks either just swap for pan head bolts. Just needs 1mm off the stl file as it catches the stop then I'll share the file https://s27.postimg.org/ijoe8krin/20170125_204947.jpg ht...