Search found 14 matches

by siquenique
21 Jan 2018, 09:45
Forum: helloBEEprusa
Topic: Issue with Calibration Addon
Replies: 4
Views: 5491

Re: Issue with Calibration Addon

Hi,

I managed to solve it, indeed the servo was not going fully to the vertical position as it should. I manually pushed a bit down and now it seems to be working just fine.

Regards,
Joao
by siquenique
19 Jan 2018, 13:48
Forum: helloBEEprusa
Topic: Issue with Calibration Addon
Replies: 4
Views: 5491

Issue with Calibration Addon

Hi, I followed all the steps for the calibration addon until the step Calibration Nozzle Height. When I press it the printer starts to move and doesn't stop even hiting the table and doing awful noise. During this i need to disconnect the printer to stop, so i cannot use the nozzle calibration. Can ...
by siquenique
14 Dec 2017, 13:11
Forum: helloBEEprusa
Topic: [FIRMWARE] Latest helloBEEprusa firmware 1.1.1 Final
Replies: 14
Views: 20629

Re: [FIRMWARE] Latest helloBEEprusa firmware 1.1.1 Final

Hi, i tried updating the firmware with the arduino 1.6.8 and didn't worked. Only managed with the 1.8.3. When you say uninstall you mean delete the arduino version and install again in the MacOS? Also how can i factory reset the arduino and do a clean install? Right now with this latest installation...
by siquenique
18 Jul 2016, 09:24
Forum: helloBEEprusa
Topic: [SOLVED] Not able to print anything
Replies: 23
Views: 26538

Re: Not able to print anything

Hi Andre,

All solved, my main issue now is that when I print most of the times the print doesn't end because is not feeding anymore. It stops feeding in the middle of the print. Are you aware of any tip for this?

Regards,
Joao
by siquenique
18 Jul 2016, 09:23
Forum: helloBEEprusa
Topic: Files for Cura 2.1.1 (testing)
Replies: 10
Views: 19609

Re: Files for Cura 2.1.1 (testing)

Hi, I tried to use this in the MAC version and I have some issues: I've added the .json file to home/.cura/machines/ and the stl to meshes folder. When I open cura all appears correctly but i cannot either Save the file (nothing is saved) or Print to USB (opens the print dialog but the temperature d...
by siquenique
16 Mar 2016, 14:17
Forum: helloBEEprusa
Topic: [SOLVED] Not able to print anything
Replies: 23
Views: 26538

Re: Not able to print anything

Hi,

That doesnt really answer my question, at least the one with the second extruder going up after i start printing. They have the same level as i mentioned and than when i start printing the right adjustment next to the stepper motor goes out of synch.

Regards,
Joao
by siquenique
14 Mar 2016, 16:28
Forum: helloBEEprusa
Topic: [SOLVED] Not able to print anything
Replies: 23
Views: 26538

Re: Not able to print anything

Hi, I've managed to fix the issue, it was related with the screws of the lever next to the wheel to be loose. Now i can print correctly. The question i have and happens frequently is: - When the print starts the nozzle 2 goes upper than nozzle 1. Although in the start they are at the same level. - B...
by siquenique
21 Jan 2016, 13:52
Forum: helloBEEprusa
Topic: [SOLVED] Not able to print anything
Replies: 23
Views: 26538

Re: Not able to print anything

Hi :) About the LCD, it seem that is a contact problem for sure!! About the extruder problem, I recommend you to see this: See the Doc. Fix & recommendations here https://beeverycreative.com/forum/viewtopic.php?f=8&t=110 and try "the Lower the hotend" part, I strongly recomend lower 2mm; You can se...
by siquenique
20 Jan 2016, 08:33
Forum: helloBEEprusa
Topic: [SOLVED] Not able to print anything
Replies: 23
Views: 26538

Re: Not able to print anything

Hi, I've tried yesterday and nothing being print. It looks better with the changes proposed, the extruder is more in the center and looks the filament fits better. Let me guide through what i did and if there are any videos or instructions how to feed the filament better. 1 - After the changes propo...
by siquenique
19 Jan 2016, 13:39
Forum: helloBEEprusa
Topic: [SOLVED] Not able to print anything
Replies: 23
Views: 26538

Re: Not able to print anything

Hi :) About the LCD, it seem that is a contact problem for sure!! About the extruder problem, I recommend you to see this: See the Doc. Fix & recommendations here https://beeverycreative.com/forum/viewtopic.php?f=8&t=110 and try "the Lower the hotend" part, I strongly recomend lower 2mm; You can se...