Page 2 of 3

Re: NEW TESTING FIRMWARE based on Marlin 1.1.0-RC3

Posted: 08 Feb 2016, 16:37
by Filipe
Hello fgarcia,

According to this post, the arduino needs to be 1.0.5:
https://beeverycreative.com/forum/viewt ... p?f=8&t=27
(about the middle of page, you can find the links)

Don't know if the same process applies to the new firmware, but since there isn't any mention of using a different on, try 1.0.5.

Also, you can PM "jpinto", since he posted this new "beta" firmware, he knows more than me.

Best regards

P.M. - Can you downgrade to the latest stable version?

Re: NEW TESTING FIRMWARE based on Marlin 1.1.0-RC3

Posted: 09 Feb 2016, 12:09
by fgarcia
Hi,

A bug?...
I haven't been able to tune the temperature of the extruder because when try by selecting it goes to the flow and doesn't give the option to go back...

Starting to go the previous version? :(

Re: NEW TESTING FIRMWARE based on Marlin 1.1.0-RC3

Posted: 09 Feb 2016, 12:27
by Filipe
My previous response was for this post:
fgarcia wrote:Hi
Since I've upload this new version to my printer I can't connect to it by USB cable...
I'm using arduino 1.0.5-r2, do I have to use other version to upload or is there anything else that i need to do?
Any progress regarding that situation?

Re: NEW TESTING FIRMWARE based on Marlin 1.1.0-RC3

Posted: 09 Feb 2016, 19:46
by LuisMonteiro
Hi

I had the same problem . I change the baud rate to 250000 .

Re: NEW TESTING FIRMWARE based on Marlin 1.1.0-RC3

Posted: 11 Mar 2016, 00:02
by regpye
I am testing the new firmware on my machine and have changed it to probe at 16 points rather than 9 points because I wasn't getting a good reading.
I am still having some issues as some parts of the bed are too high and some parts are too low.
I can get a grid reading and have notes the readings on paper and checked several times, the reading only changing about .01 or .02 over several tests. However, when I come to do a print, the nozzle is pressing hard against the bed in one corner and way above the bed in another corner.
Seems like the readings are not being saved??
Any ideas what could be wrong?

Re: NEW TESTING FIRMWARE based on Marlin 1.1.0-RC3

Posted: 14 Mar 2016, 15:21
by jorge
Hi regpye.

Please follow the latest Latest Assembly and User manuals for the calibration: http://beeverycreative.com/forum/viewto ... ?f=8&t=327

Re: NEW TESTING FIRMWARE based on Marlin 1.1.0-RC3

Posted: 31 Mar 2016, 22:16
by fennec_inc
Testing this version works fine so far for me, today though I came across a bug which prevents me from using it with the RepRap Discount Graphic LCD controller. When I uncomment the section in the config.h (as shown in the RepRap Wiki) compiling fails with an error in ultralcd.cpp ("lcd was not declared in this scope" ).
Apparently there is some error/something missing at the point where the menu for loading and unloading the filament is displayed

Re: [FIRMWARE] helloBEEprusa based on Marlin 1.1.0-RC3

Posted: 30 Apr 2016, 17:30
by mario
Hello everyone,

Quick question, how can i downgrade the Marlin firmware to the original one that comes with the HelloBEEPrusa?

Thank you,

Mario

Re: [FIRMWARE] helloBEEprusa based on Marlin 1.1.0-RC3

Posted: 02 May 2016, 11:27
by jorge
Mario,

You can downgrade the firmware to this one: https://github.com/beeverycreative/hell ... a-firmware

Re: [FIRMWARE] helloBEEprusa based on Marlin 1.1.0-RC3

Posted: 02 May 2016, 15:49
by Filipe
Mario,

Have your tried uploading a previous version, following the Manual?
https://beeverycreative.com/manuals-tutorials/

Check page 24

Direct link to the current version:
https://beeverycreative.com/wp-content/ ... 160308.pdf