Search found 223 matches

by MrDoom
17 Apr 2018, 10:35
Forum: helloBEEprusa
Topic: Last Firmware setting modification of T1 offset
Replies: 1
Views: 2746

Re: Last Firmware setting modification of T1 offset

Hello there, You should be able to edit the values so they are: #define HOTEND_OFFSET_X {0.0, 69.75} // (in mm) for each extruder, offset of the hotend on the X axis {0.0, 67.5} is original value #define HOTEND_OFFSET_Y {0.0, -0.4} // (in mm) for each extruder, offset of the hotend on the Y axis {0....
by MrDoom
16 Apr 2018, 12:54
Forum: helloBEEprusa
Topic: hardened steel nozzle
Replies: 1
Views: 3074

Re: hardened steel nozzle

Hello Chriz, Yes the brass nozzles do wear out quite fast with carbon fiber or glow in the dark filaments, I only tried a stainless steel nozzle for a while, it required a higher printing temperature for the same print speed, aprox +10ºC, I also noticed PLA appears to get more stuck and has more pro...
by MrDoom
16 Apr 2018, 12:50
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 59528

Re: Change DRV8825 to SilentStepStick TMC2208

Hello there Rick Rick,

According to the datasheet of the TCM2208, with the motors suplied with the helloBEEprusa you can use up to 2.40V without exceding the motor limit, try increasing it slowly until you have no more problems :)
by MrDoom
11 Apr 2018, 17:42
Forum: helloBEEprusa
Topic: [SOLVED] Constant Y-Axis Shift Issue
Replies: 3
Views: 11129

Re: Constant Y-Axis Shift Issue

Hello Mario, Sad to know that your printer is acting out but I think we will be able to fix it. First of all make sure that your axis are correctly lubed and that you adjusted the stepper driver current (page one of the fixes document https://beeverycreative.com/forum/download/file.php?id=62), also ...
by MrDoom
03 Apr 2018, 11:19
Forum: helloBEEprusa
Topic: Bed Heating and extruder temp issues
Replies: 4
Views: 5120

Re: Bed Heating and extruder temp issues

Hello there, I can assure you the printbed will reach and surpass 110ºC when correctly set up, most of the times what happens is the small temperature sensor on the bed gets dislodged from it's correct position on the center of it (there is a small hole) and thus the board reads the wrong value, ano...
by MrDoom
03 Apr 2018, 11:06
Forum: helloBEEprusa
Topic: Filament input help
Replies: 3
Views: 5321

Re: Filament input help

Hi there, Are you talking about a Beethefirst or a helloBEEprusa? If it is the helloBEEprusa, you posted this in the wrong place. Also the helloBEEprusa, at least mine never worked that well with PLA from BQ, mostly due to the full metal hotend, the BQ PLA seems to have a lower melting point and tha...
by MrDoom
22 Mar 2018, 12:16
Forum: helloBEEprusa
Topic: Dual extrusion
Replies: 1
Views: 2928

Re: Dual extrusion

Hello ackbahr, What material are you using as suport material? I tried using PVA before but I was unable to get it to print properly, later I discovered PVA is very very difficult to be used with full metal heatbreaks as it adheres too much to the walls making the extrusion almost impossible. I have...
by MrDoom
21 Mar 2018, 17:05
Forum: helloBEEprusa
Topic: [INFO] Fix for Hello BEE prusa (freezes or heats too much)
Replies: 23
Views: 30100

Re: [INFO] Fix for Hello BEE prusa (freezes or heats too much)

Hi there tomemayes, Before trying anything else try following ALL the fixes present here, starting with the ones refering to the endstops (older versions had a extra pin that was supposed to be cut) and updating the firmware (LOTS of bugfixes/improvements have been made). https://beeverycreative.com...
by MrDoom
16 Mar 2018, 14:38
Forum: BEESOFT
Topic: Beesoft 4 install Help!
Replies: 1
Views: 3976

Re: Beesoft 4 install Help!

Hello there! On the blanck screen try pressing Alt and clearing the cache, then using the task manager(Ctrl+Shift+Esc), then go to the services tab, right click on BEESOFT and restart the service, then go to the software again and restart the window and press Ctrl+R to refresh the interface, it shou...
by MrDoom
13 Mar 2018, 12:31
Forum: GENERAL
Topic: hello guy
Replies: 9
Views: 13593

Re: hello guy

Hello there Shardhhajain23, if you need any help or advises regarding 3d printing feel free to ask :)