Search found 8 matches

by jaume.figueres
10 Feb 2020, 11:00
Forum: B2X300
Topic: SD card acces
Replies: 1
Views: 162

SD card acces

Hi,
I'm newby so please enlight me.
I been tring to find the best way to send gcode to SD card of my B2X300 from Cura 4.4. I tried via Octoprint but, when Octoprint is conected I can't acces SD from the machine itself.
by jaume.figueres
10 Feb 2020, 10:37
Forum: B2X300
Topic: [FIXED] I'm missing somehing EC11 then EC61 & EC11 again
Replies: 4
Views: 445

Re: I'm missing somehing EC11 then EC61 & EC11 again

Now my printer is working, after realizing I had a defective main board Paulo from support has sended me a new board (hope you feel better) and after a couple of extra weeks, everything seems ok. I have to say that, you have been kind and nice to me and solved the problem without any objection.not f...
by jaume.figueres
19 Jan 2020, 11:42
Forum: B2X300
Topic: E0 and E1 are not working - suddenly
Replies: 3
Views: 401

Re: E0 and E1 are not working - suddenly

Hi,
does you find any solution, here E1 (E0 never worked, I'm waitinf for a new mother board) motor has suddenly stoped working too.

I was wonderingif you found any solution.

thanks
by jaume.figueres
09 Jan 2020, 19:26
Forum: B2X300
Topic: Can't set printer up EC11 & EC61
Replies: 3
Views: 341

Re: Can't set printer up EC11 & EC61

I'm new to all this, and get really stucked, I wanna try to skip selftest program but I don't know how to do that, this is my first contact with 3d printers, but I have experience in electronics, laser cutting machines and arduinos, RP etc...

can anybody please give me a hand on this

thanks
by jaume.figueres
09 Jan 2020, 12:42
Forum: B2X300
Topic: Can't set printer up EC11 & EC61
Replies: 3
Views: 341

Re: Can't set printer up EC11 & EC61

Thnks tgala HI, I allready cheked EC codes, and run test step by step, EC 61 is Power loss detection, as I mentioned before, and EC11 is first step and is Exruder temp sensor, I tried to swap sensors and still the same so I gess is not de sensor. anyway it worked nicely first time i run selftest (un...
by jaume.figueres
09 Jan 2020, 11:11
Forum: B2X300
Topic: Can't set printer up EC11 & EC61
Replies: 3
Views: 341

Can't set printer up EC11 & EC61

Hi, after assembling printer and update firmware I'm getting stuck in self test program. first attempt EC11 shows up, after rebboting test program run to "powerloss" and EC61 arrives, after some reboots EC11 again, I need some help because I doublecheked conections(even I swaped the extruder sensors...
by jaume.figueres
08 Jan 2020, 20:12
Forum: B2X300
Topic: [FIXED] I'm missing somehing EC11 then EC61 & EC11 again
Replies: 4
Views: 445

[FIXED] I'm missing somehing EC11 then EC61 & EC11 again

Hi, first of all hello to everyone's I just ensambed my printer then upgraded and serial nuber entered, everythings fine untill selftest run. firts time I run it stops on 1st step (extruder 1 EC11) restart an test runs ok untill power loss detector (EC61), restart again sevearl times with same resul...