Search found 109 matches

by DomingosRodrigues
13 Aug 2019, 15:35
Forum: BEETHEFIRST
Topic: Extruder motor not moving
Replies: 2
Views: 57

Re: Extruder motor not moving

Hello frosteryd, With regular use the planetary gearbox inside the extruder motor can wear away, resulting in the extruder not being able to push the filament, to fix it usually we recommend sending the printer to Beeverycreative as it only happens to printers with some wear that require some extra ...
by DomingosRodrigues
09 Aug 2019, 14:53
Forum: B2X300
Topic: Nozzle Details
Replies: 2
Views: 54

Re: Nozzle Details

Hello HansMeiser, The default nozzle for the B2X300 is the MK8 nozzle that can be found on various online shops, or can be acquired through us if you contact sales@beeverycreative.com, I would recmmend agains buying the cheapest ones available from china as those usually reduce the print quality and...
by DomingosRodrigues
07 Aug 2019, 18:32
Forum: BEESOFT
Topic: Y axis moving on the opposite direction
Replies: 3
Views: 308

Re: Y axis moving on the opposite direction

Hello Kamdype,

Have you tried the suggestion I made on the previous post?

Best regards
Domingos Rodrigues
by DomingosRodrigues
05 Aug 2019, 14:23
Forum: B2X300
Topic: B2X300 the printer from hell
Replies: 18
Views: 1602

Re: B2X300 the printer from hell

Hello Wayne, sorry for the delayed answer, I was away for a few weeks, what problem did you have now? Did the board stop working or are you mentioning the stepper drivers? You can buy plug and play replacements for the TMC2130 from other companies, like Waterrot, Fysetc, etc. our version has some op...
by DomingosRodrigues
05 Aug 2019, 14:01
Forum: helloBEEprusa
Topic: Bee Prusa - no controller response when powered on
Replies: 2
Views: 83

Re: Bee Prusa - no controller response when powered on

Hello Langdon, Sorry for the delay in approving the post, I was on vacation :) For fast assistance please contact customer_service@beeverycreative.com As for your problem have you adjusted the LCD contrast? There is small potentiometer on the back side of the LCD, it controls the contrast of the scr...
by DomingosRodrigues
18 Jul 2019, 17:07
Forum: B2X300
Topic: Is Bed leveling not working for anyone else?
Replies: 1
Views: 555

Re: Is Bed leveling not working for anyone else?

Hello Waine, I've had some similar problems with the leveling and it turned out to be a lack of squareness between the axis, especially the Y axis whose rods were slightly higher on one side than the other causing the whole printer to missread the bed. Try losening all rod holders from the frame and...
by DomingosRodrigues
12 Jul 2019, 12:10
Forum: B2X300
Topic: Filament slipping
Replies: 2
Views: 246

Re: Filament slipping

Hello Raven, The motor/Stepper driver combo on the B2X300 has been tested on various filaments and no such problems are observed if you follow the recommended procedures and configure the profile accordingly, most importantly: - Ensure the Filament oiler is well damped in WD40 especially on ALL PLA ...
by DomingosRodrigues
05 Jul 2019, 11:41
Forum: helloBEEprusa
Topic: Nozzle extruding 'wavey' material
Replies: 3
Views: 1315

Re: Nozzle extruding 'wavey' material

Hello BarryInnob,

The problem seen on the photo posted before is caused by incorrect adjustment of the Z axis endstop.

If you Ultimaker 2 doesn't do it, you did a good job calibration it :) As for the prime line it can also easily be applied on the helloBEEprusa if it is required.

Best regards
by DomingosRodrigues
03 Jul 2019, 13:58
Forum: B2X300
Topic: Tips on how to remove stuck PLA
Replies: 4
Views: 294

Re: Tips on how to remove stuck PLA

Hello MrBrokeSheet, I would not recommend completely disassembling the extruder assembly if not necessary as it will increase the chance that something is in an incorrect position. The correct method of cleaning the oozed plastic is the one I described above. The plastic inside the heatzone will be ...
by DomingosRodrigues
03 Jul 2019, 12:51
Forum: B2X300
Topic: Tips on how to remove stuck PLA
Replies: 4
Views: 294

Re: Tips on how to remove stuck PLA

Hello MrBrokeSheet, Please try heating the nozzle using the change filament option, select the extruder, then the material and dont select a operation, the hotend should heat up and stay at the temperature then you can clean the oozed plastic using some tissues or even a cloth rag, being very carefu...