Search found 77 matches

by DomingosRodrigues
15 May 2019, 11:12
Forum: BEETHEFIRST
Topic: Problem with driver
Replies: 4
Views: 4039

Re: Problem with driver

Hello byronSoitA and Trawrans,

Please try following the suggestion given by mgomes and if that doesn't work report back :)

Best regards
by DomingosRodrigues
10 May 2019, 14:43
Forum: helloBEEprusa
Topic: [FIRMWARE] Latest helloBEEprusa firmware 1.1.1 Final
Replies: 13
Views: 14773

Re: [FIRMWARE] Latest helloBEEprusa firmware 1.1.1 Final

Hello Kedar, the latest firmware has new PID factor for the extruder heater control, they are tuned to the defaul heater, block and temperature sensor, make sure both the heating element and sensor are correctly inserted and tightened on the hotend you see the problem. If that doesn't work you can c...
by DomingosRodrigues
07 May 2019, 14:14
Forum: helloBEEprusa
Topic: Feeder hack
Replies: 1
Views: 71

Re: Feeder hack

Hi apocas, Really nice job on the customization, looks really clean :D I'm sorry to know you had problems with the original extruder, it is a little more finicky than the one you installed mostly due to the manual filament tension adjustment that requires tuning for every material. Personally never ...
by DomingosRodrigues
06 May 2019, 11:39
Forum: helloBEEprusa
Topic: [3D PARTS] helloBEEprusa 3D printer KIT printed parts
Replies: 32
Views: 37226

Re: [3D PARTS] helloBEEprusa 3D printer KIT printed parts

Hello kedar,

please follow the user manual for some help, present here: https://beeverycreative.com/wp-content/ ... 70707-.pdf

Usually you only need to drag and drop the file onto cura once it is configured :)

Best regards
Domingos Rodrigues
by DomingosRodrigues
06 May 2019, 11:35
Forum: helloBEEprusa
Topic: Connection Issue
Replies: 1
Views: 54

Re: Connection Issue

Hello lacaca, The bearings are usualy a little tighter out of the box and need some run time to loosen up, nonetheless the printer includes a extra bearing, try changing the bearings around trying on which work on which rod, if you find it really stuck you can try cleaning them out with isopropyl al...
by DomingosRodrigues
28 Apr 2019, 16:38
Forum: B2X300
Topic: Error Code EC51 after firmware update
Replies: 2
Views: 152

Re: Error Code EC51 after firmware update

Hello TracyJonSargeant, Adding to what Silvia mentioned, the error you have is due to a problem with a stepper driver, most likely a bad connection between either the communication board (white board bellow the air channel on the motherboard) and the stepper drivers (small white chips on the motherb...
by DomingosRodrigues
25 Apr 2019, 17:52
Forum: BEETHEFIRST
Topic: Can't update firmware?
Replies: 11
Views: 337

Re: Can't update firmware?

Hi Ben,

I'm glad the older version of BEEsoft fixed the firmware issue, if you have any other issues feel free to ask :)

Best regards
by DomingosRodrigues
25 Apr 2019, 17:51
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 32176

Re: Change DRV8825 to SilentStepStick TMC2208

Hello Benji, 0.85V on the potentiometer, considering the stepper drivers current measurement resistors are equal to the original (some chinese clones change it) means you are providing 0.6A which is a little low for the original stepper motors which are rate at 1.68A. I would recommend raising it to...
by DomingosRodrigues
23 Apr 2019, 19:39
Forum: BEETHEFIRST
Topic: Can't update firmware?
Replies: 11
Views: 337

Re: Can't update firmware?

Hi Ben,

Once again, please contact customer_service@beeverycreative.com there is something wrong going on, it appear to be on the software side and we need to perform some tests on both your PC and printer to be able to help you.

Best regards
by DomingosRodrigues
23 Apr 2019, 19:28
Forum: BEETHEFIRST
Topic: Can't update firmware?
Replies: 11
Views: 337

Re: Can't update firmware?

Try restarting beesoft when you restart the printer the printer, that might help.But most likely some other program or service you have on your PC is interfering in the communication with the printer during boot. Nonetheless you can try reconnecting after resetting, but the printer should automatica...