Search found 128 matches

by HALFORD
26 Mar 2020, 20:42
Forum: helloBEEprusa
Topic: HELLO BEE PRUSA DIED
Replies: 1
Views: 559

HELLO BEE PRUSA DIED

HI ALL, been printing some parts recently and noticed the occasional odd sounds from axis moves and also lots of missed steps in Y axis. today started a print at reduced feed @70% less for ALL moves. Made sure the first 2-3 layers looked good then left it to it. came back to check every few mins the...
by HALFORD
17 May 2018, 19:22
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 54947

Re: Change DRV8825 to SilentStepStick TMC2208

Hello, thanks for the reply.
I believe my problem lies in having an inductive probe fitted.
I'll contact customer support for help.
Halford
by HALFORD
15 May 2018, 17:31
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 54947

Re: Change DRV8825 to SilentStepStick TMC2208

Have you guys any problems with auto home after installing?
by HALFORD
12 May 2018, 14:40
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 54947

Re: Change DRV8825 to SilentStepStick TMC2208

Guys, I finally fitted 5 off 2208's. XYZ now very quiet. Only problem is Z axis travels wrong direction when homing (Z+). Have tried various inverting directions of endstops to correct but no luck. Can anyone suggest what to change in the firmware? Normal xyz axis movement by manual mode are correct...
by HALFORD
08 Mar 2018, 19:24
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 54947

Re: Change DRV8825 to SilentStepStick TMC2208

Mr. Doom, thanks for your reply.
If you leave the 8825 in place for the Z axis will it do any harm or overheat.
Does the 8825 function as normal even though you have the firmware set to use 2208?

Regards
by HALFORD
07 Mar 2018, 20:47
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 54947

Re: Change DRV8825 to SilentStepStick TMC2208

Hello, I have 3 tmc2208 to fit.
I was planning on just fitting to the X Y AXES only, and leave the original 8825 in the Z axis.
Does anyone know if this will be ok?
The firmware states 2208 all or extruder as choices.
I only want to improve xy noise.
by HALFORD
15 Feb 2018, 19:23
Forum: helloBEEprusa
Topic: Change DRV8825 to SilentStepStick TMC2208
Replies: 44
Views: 54947

Re: Change DRV8825 to SilentStepStick TMC2208

Hi, Toms hardware has reviewed these and the configuration.

https://toms3d.org/2015/01/29/honest-up ... stepstick/
by HALFORD
17 Jan 2018, 19:48
Forum: helloBEEprusa
Topic: Auto Leveling
Replies: 18
Views: 22655

Re: Auto Leveling

Hello Benji, sorry to hear you have problems with the sensor. The first one i bought also did not work, it was permanantly on. After buying another of the same make it was ok. I did not need to fit resistors as you rightly say. i think the only solution is to buy another switch. I did get a refund f...
by HALFORD
20 Dec 2017, 20:25
Forum: helloBEEprusa
Topic: Auto Leveling
Replies: 18
Views: 22655

Re: Auto Leveling

Benji, keep me informed of the progress. Happy to help.
by HALFORD
20 Dec 2017, 20:24
Forum: helloBEEprusa
Topic: Filament jams mid print
Replies: 14
Views: 14754

Re: Filament jams mid print

Mr Doom, this is very usefull information.
Do you have any problems with stringing at such a low retraction?
Regards Halford